Exposure Compensation

Exposure Compensation

In many extreme situations, you perhaps should not trust the exposure information provided to you by the camera exposure meter. In these cases, you need to use Exposure Compensation for exposure adjustment. This can be done easily with the +/- button on the top panel and the command dial:

Press the +/- button while turning the command dial to increase or decrease the compensation level. Coolpix 4500 permits a 1/3 stop increment/decrement. More precisely, turning the command dial clockwise (resp., counter-clockwise) increases (resp., decreases) the compensation level in +1/3 stop (resp., -1/3 stop). The range of the compensation level is from -2 stop to +2 stop.

While the command dial is being turned, the selected compensation level is shown near the upper-left corner of the monitor as shown below. The compensation values are rounded and, as a result, the displayed values are -2.0, -1.7, -1.3, -1.0, -0.7, -0.3, 0.0, +0.3, +0.7, +1.0, +1.3, +1.7 and +2.0. Therefore, with the current setting of aperture and shutter speed, we still have plus-minus 2 stops for fine-tuning exposure. Note that the monitor does not display compensation level 0.0 stop.

Note that once this option is chosen, it will stay there even after turning off the camera. Therefore, you need to go through the above procedure again to reverse the setting..

Why Is Exposure Compensation Necessary?

A camera's exposure meter is always calibrated at the so-called middle gray level, which means the gray color that is in the middle between complete white and complete black and reflects 18% of the incoming light. When you point your camera at your subject and take a meter reading, the meter will consider the intensity of light being read as middle gray. This creates problems!

Suppose most areas in your scene is white, say snow covered. The exposure meter will treat that white area as mid-gray. When you take your shot, the white area looks grayish. The image below shows a snow covered area, and, as a result, the camera exposure meter considers this white area being mid-gray if no compensation is applied. So, the snow covered area looks grayish.

No Compensation
Click on the icon to see a larger image

Because the exposure meter treats white as gray in the image, to make a gray color a white one, we need to increase the exposure with the +/- button. The images below were taken in 1/3 stop increment. As you can see, when the compensation is set to +1 stop, the snow covered area starts to look white. As compensation increases, some details are lost and the washed-out (or blown out, as many prefer) effect appears. Check the sky and the lower-right corner of the images.

+1/3 stop +2/3 stop +1 stop
+1 1/3 stop +1 2/3 stop +2 stop
Click on the icon to see a larger image

On the other hand, if a scene contains a dominating black subject (e.g., black cat, ;-)), the camera exposure meter will consider this black subject a middle gray one. Hence, the black subject will be over-exposed as shown in the first image of the top row below. To overcome this problem, we need to decrease the exposure so that black subjects look black. The following shows a sequence of images taken with negative compensation. These images show that as the exposure decreases, the black camera looks darker and the over-exposed background starts to show details.

No compensation -0.3 stop -0.7 stop -1.0 stop
-1.3 stop -1.7 stop -2.0 stop
Click on the image to see a larger one

In general, if your subject is bright, you perhaps need to increase the compensation level so that the bright area looks white. On the other hand, if your subject is dark, you should decrease the compensation level to make the subject darker.

Other Common Uses

The most commonly seen situation is backlighting. That is, the light sources are behind your subjects (i.e., your camera points at light sources). In this situation, the subjects are not illuminated by the light sources and hence look dark. The left image is an example. Because we need to emphasize the subjects rather than the background, exposure has to be increased to show the details of the subjects. Thus, I chose to increase exposure by one stop and obtained the right image below. Now the details can be seen clearly.

No compensation +1 stop
Click on the icon to see a larger image

Another frequently encountered situation looks like the left image below. This scene contains two areas, one in the shadow and the other under strong sunlight. It is a challenging situation for an on-camera meter, and, as a result, the background (light) area may be exposed correctly while the foreground could become too dark. Should this happen, the use of exposure compensation is a better strategy. The middle image was taken with a 2/3 stop increase, while the right one has 1 1/3 stop. Note that the middle one has a better balance than the right one because it preserves the background and also includes foreground details. The right one exposes the foreground very well, but the background is washed out.

No compensation +2/3 stop +1 1/3 stop
Click on the icon to see a larger image

What is "the" Correct Exposure?

It is really difficult to answer this question, because it depends on your artistic point of view. An exposure value you like may not be a good one from a different point of view. The following shows three images taken about the same time. The left one has no compensation. But, I know I would get an over-exposed image without some of the (color) details if I increase the compensation level. Therefore, I did not even try to increase the compensation level. The middle and the right images have -0.7 and -1.7 stop decrements, respectively. So, the one you like most has "the" correct exposure!

No Compensation -0.7 stop -1.7 stop
Click on the icon to see a larger image

Coolpix 4500 has a nice feature, Auto Bracketing, for you to take a sequence of images, each of which has a different compensation value chosen from a pre-selected sequence. In this way, you do not have to adjust exposure compensation for each image.

By the way...

There is a clumsy way of setting exposure compensation, although I do not think you will often use it because it goes through the menu system. However, if the +/- is redefined to have a different meaning, the following procedure becomes useful:

  1. Set the camera to the P mode, A mode, S mode or M mode by holding the MODE button and turning the command dial at the same time.
  2. Press the MENU button once to enter the first page of the SHOOTING MENU. You will see the following screen:

  3. Use the down arrows of the multi-selector to enter the menu system. The first menu item is highlighted as shown in the left image below. Then, press the MENU button twice to enter the third page as shown in the right image below.

        

  4. The first option Exposure Options is what we need. So, use the right arrow of the multi-selector to make a selection. Then, the following screen appears. There are two options. The second one, Exp. +/- is what we need. Note that the previously set compensation level is show to the left of Exp. +/-. So, use the down arrow of the multi-selector to highlight this item.

        

  5. Now, use the right arrow of the multi-selector to select this option. A list of all possible compensation level is shown with the current setting highlighted as shown in the left image below.

        

    Use the up and down arrow to highlight the desired compensation level and press the multi-selector button to make a selection. In the right image above, it shows the compensation level of +1.0 stop is highlighted.

  6. Once the above steps complete, press the MENU button twice to return to the shooting mode.

    Note that once this option is chosen, it will stay there even after turning off the camera. Therefore, you need to go through the above procedure again to reverse the setting..